Just how do you actually feel when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a bathtub isn't specifically brain surgery, but it does call for solid plumbing, carpentry, and often, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably hard task. If the old bathtub is readily accessible, the project can relocate speedily; if you need to open up a wall to get rid of the old bathtub and position the brand-new tub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will certainly need a helper to vacate the old bathtub and embeded in the new one. See to it you have actually qualified on your own for the work as well as fit attempting it. Rather than hiring a service provider to take control of a halfway-completed project, it is better to consider employing one prior to you begin. Chances are you might need an expert plumber to make tube links.
This article will assist you mount a new bath tub in your shower room if you have actually already gotten a brand-new tub as well as don't require to transform the arrangement of your previous water system pipelines.
Your devices and material list need to make up the following:
Preparing for the Installation
To start with, the sustaining framework supplied with the bathroom needs to be fitted (if needed) according to the supplier's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is necessary to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps device to prevent stress on the bath tub.
Fit the adaptable faucet adapters to the bottom of the two taps utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its final placement.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, after that the first thing you must do is detach the water supply. After doing so, activate the taps to drain any kind of water staying in the system. The procedure of eliminating the existing faucets can be fairly troublesome because of the limited access that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the faucets. Have a towel all set for the remaining water that will come from the pipelines. When the supply pipes have been eliminated, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from turning throughout this procedure. Once the faucets have been removed, the holes in the bath/basin will have to be cleaned of any kind of old sealing substance.
Prior to going on to fit the new faucets, contrast the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Tub
Using the two wood boards under its feet, position the bath tub in the required position. The wood boards are helpful in evenly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto four little points.
The following objective is to make certain that the bathtub is leveled all round. This can be attained by inspecting the level and also adjusting the feet on the tub until the spirit level checks out level.
To set up taps, fit the bottom of the outermost adaptable tap connector to the suitable supply pipe by making a compression join; then do the same for the other faucet.
Turn on the water system and inspect all joints and also new pipework for leakages and also tighten them if required. Load the bath tub and additionally check the overflow outlet as well as the regular electrical outlet for leakages.
Finally, repair the bathroom paneling as explained in the supplier's user's manual. Tiling and sealing around the bathtub should wait until the bathtub has been made use of at least when as this will certainly resolve it right into its final position.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the other end gives a link to the existing supply pipelines.
If you need to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in place in between the faucet and the sink. Protect the faucet in place with the maker given backnut. Once the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The former type should be connected to the tap ends first, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bath fulfills the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to split a rigid seal, creating the water to permeate the wall surface in between the bathroom as well as the tiling, causing problems with dampness and also possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components and fittings. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill the bathtub with water before securing, to allow for the movement experienced when the tub is in use. The sealant can break relatively very early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently readily available on the market. It is recommended to fit the ceramic tiles using waterproof or waterproof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you liked our part on Installing A Bathtub. Thank you for spending some time to browse our posting. Loved our piece? Please share it. Help others locate it. I cherish reading our article about A Step-by-Step Guide to Installing a Bathtub.
Reliable help, dial now.